- - AGRICULTURE CORE CURRICULUM - - (CLF2000) Advanced Core Cluster: AGRICULTURAL MECHANICS (CLF2450) Unit Title: PROJECT DESIGN ___________________________________________________________________________ (CLF2451) Topic: PREPARING A WORKING Time Year(s) DRAWING 2 hours 1/2/3/4 ___________________________________________________________________________ Topic Objectives: Upon completion of this lesson, the students will be able to: Learning Outcome #: (J-1) - Identify the different types of lines used in a drawing or layout. (J-2) - Identify the three types of drawings (orthographic, isometric, and oblique). (J-3) - Use an architect's scale. (J-4) - Construct three-view (orthographic) drawings. (J-6) - Sketch an object, using paper and pencil. Special Material and Equipment: Architect's scale, pencils, paper, drawing board, T square, 45 degree triangle (8" long sides), 30 degree X 60 degree triangle (10" side), cross-ruled paper, tracing vellum References: Burke, Stanley R., & Wakeman, T. J. (1990). MODERN AGRICULTURAL MECHANICS (2nd ed.). Danville, IL: Interstate Publishers. Cooper, Elmer L. (1987). AGRICULTURAL MECHANICS: FUNDAMENTALS AND APPLICATIONS. Albany, NY: Delmar Publishers. Jones, M. M. (1955). SHOPWORK ON THE FARM (2nd ed.). New York: McGraw-Hill. Spencer, H. C., & Dygdon, J. T. (1980). BASIC TECHNICAL DRAWING. New York: Macmillan. Resources: Bear, W. F., Hamilton, W. H., & Mann, A. (1974). PLANNING PROJECT CONSTRUCTION. Available from Hobar Publications, 1234 Tiller Lane, St. Paul, MN 55112 (612) 633-3170 Evaluation: Completion of a sketch and a working drawing of a project to be constructed. TOPIC PRESENTATION: PREPARING A Working Drawing A. Sketches and Working Drawings 1. Sketches are freehand drawings of an object for a project done in order to get the idea down on paper. a. Sketches are not usually drawn to scale. b. Neatly drawn sketches with fairly accurate dimensions are usually sufficient for simple projects. c. Sketches of larger and more complicated projects can serve as the basis for accurate working drawings. 2. Working drawings are complete drawings done in universal graphic language so that the object depicted can be constructed from the drawing alone without additional information. a. Dimensions - Working drawings use lines scaled to the dimensions of the actual objects. b. Views - Working drawings show specific views of an object with enough detail to enable project construction.` 1) Most working drawings show three separate sides of an object from three flat, head-on views. 2) Pictorial drawings show three sides of an object together in one view. B. Types of Working Drawings 1. Orthographic Drawings a. They show a flat, head-on view of every side that differs in size and shape. b. They may illustrate six views of the object: top, bottom, front, back, right side, and left side (the ends). c. They usually use only three views: top, front, and end. 2. Pictorial Drawings a. Isometric Drawings 1) Isometric drawings are based on three lines or axes: one vertical axis with two others at 60 degrees to the vertical. 2) Such drawings can show the true dimensions of an object's top, side, and end views. 3) The line angles of isometric drawings are not accurate, but are nevertheless used to give the object a three dimensional effect. b. Oblique Drawings 1) Oblique drawings are based on three lines or axes similar to isometric drawings, except that one axis is horizontal, one vertical, and the third is at a convenient angle (typically 30 degrees to 45 degrees) to the horizontal. 2) Like isometric drawings, oblique drawings can depict the true dimensions of an object's top, side, and end. 3) The front of an oblique drawing always shows the true shape of that side of the object from a head-on view. 4) If the object being drawn has a side with curved or irregular lines, this side is used for the front. SAFETY IN SKETCHING, DRAWING, AND PLAN READING* Some pieces of drawing equipment have sharp points; therefore, when using these drawing instruments, you should exercise care to prevent injury to yourself and/or others. Safety Practices 1. Keep sharp-pointed drawing instruments stored in their case to prevent injury to yourself and/or others. 2. When using drawing instruments, lay them in a safe place to prevent them from falling. 3. To prevent drawing instruments from falling, fasten the drawing table top securely before you start to draw. 4. Never play with sharp-pointed drawing instruments. C. Constructing Working Drawings 1. Drawing to Scale a. Scale drawing permits the size of the object to be reduced proportionally in order for it to be drawn on the size of paper chosen. b. Common scales of a drawing may be 1/8," 1/4," 3/4," 1," and 3," to represent one foot. For example, 1/8 inch = 1 foot. c. An architect's scale is the most common type of scale used for drawing agricultural projects. 1) Its main divisions at the end of the scale, which are in inches or fractions of an inch, represent one foot. 2) The divisions are subdivided even smaller to represent inches and fractions of an inch. 3) An architect's triangular scale has six faces with a different scale on each end of each face. d. Use of engineer's paper (graph paper) permits drawing to scale without an architect's scale. It is cross-ruled paper with 4, 8, or 12 divisions to the inch. Simply count the number of divisions in order to draw a line to scale. 2. Sheet Layout a. Attach a sheet of paper to the drawing board with tape. 1) If a T square and triangles will be used as drawing aids, use the T square to align the paper with the left edge of the drawing board. 2) If a T square is not available, tracing paper or vellum may be attached with engineer's paper under it to serve as a drawing aid. b. Draw border lines 1/2 inch from the paper's edge. c. Make a title block at the bottom of the paper which includes the following information about the drawing: 1) The name of the person doing the drawing. 2) The date of the drawing. 3) The title of the drawing. 4) The scale of the drawing. ===================================================================== *** INSTRUCTORS PLEASE NOTE *** See Cooper (p. 200) for a sample drawing. ===================================================================== 3. Types of Lines Used in Drawings a. Border line: a heavy, solid line drawn parallel to the edge of the drawing paper. b. Object line: a solid line representing the visible edges and form of an object. c. Hidden line: a series of dashes which indicate the presence of hidden edges. d. Dimension line: a solid line with arrowheads at both ends to indicate the length, width, or height of an object. e. Extension line: a solid line indicating the exact area specified by a dimension. f. Break line: a solid, zigzag line which indicates that part of the object being drawn is not fully illustrated or has been left out. g. Center line: a long-short-long line used to depict the center of a round object. h. Leader line: a solid line with an arrow pointing from an explanatory note to a specific feature of an object. 4. Developing the Views a. Choose an appropriate scale which will allow all views to fit within the border lines. b. Locate and mark off the spaces for the various views. c. Establish the main lines of the drawing, then add the minor ones. d. Develop all the views together. In a three-view, orthographic drawing, project from the front view to the top and end views with the T square and triangles. 1) Use the T square against only the left edge of the board for drawing horizontal lines, since the board may not be perfectly square. 2) Use a right-angle triangle with the T square to draw vertical lines. e. Finally, add the dimension lines and notes. _________________________________________________________ ACTIVITY: 1. Make a freehand sketch of a simple shop project. Engineer's paper can be used. 2. Develop an orthographic drawing from the sketch of the above project. _________________________________________________________ ===================================================================== *** INSTRUCTORS PLEASE NOTE *** Cooper (pp. 202-208) gives a step-by-step procedure for making an orthographic drawing of a show box. ===================================================================== 6/12/91 OLR/tf #%&C